Grub updating premiumdating ru

The only EFI Boot I have is when I hit F9 when it starts up. I think you can make some guesses which one is your kali filesystem to replace the variable gptx. Once you boot into kali open terminal and type: update-grub grub-install /dev/sda I still don't know which grub prompt you are mentioning. After entering normal it should have taken you to grub boot screen. Anyway If you are unfamiliar with commands then do one thing. So I my case, this command should be grub-install /dev/sdi Right?Either it is grub rescue mode command-line screen or actual grub menu to boot OS. If nothing is working for you the very first post is the right solution. Thanks for this guide and for the reply, and sorry if this question is kind of dumb.Enhancements to GRUB are still being made, but the current released versions are quite usable for normal operation. For the differences between GRUB Legacy and GRUB, see the Grub Legacy Documentation.If you have dual booted kali with Windows 10 then most probably you are running PC with UEFI firmware. The kernel, in turn, initializes the rest of the operating system (e.g. GRUB 2 has replaced what was formerly known as GRUB (i.e.

Just select Boot from EFI just below the Windows Boot Manager. Thought I'd check first, before causing any problems.

Like mine is /dev/sda6 /dev/sda is your EFI partition which is most likely /dev/sda1. If you are in grub rescue mode, then run these commands to reconfigure grub: ls set root=(hd0,gptx) set prefix=(hd0,gptx)/boot/grub insmod normal normal ls(LS) lists all the partitions of your hard drive like this (hd0) (hd0,gpt1) (hd0,gpt2).

You can make some guesses which one is your kali filesystem to replace the variable gptx. The right commands are: set root=(hd0,gpt3) set prefix=(hd0,gpt3)/boot/grub insmod normal normal It wasn't tough to guess that it might be gpt3. However, this line is confusing me: grub-install /dev/sda Is that correct?

I had previously been using unetbootin to create the image for the install. Disk /dev/sdb: 7.7 Gi B, 8242855936 bytes, 16099328 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0x17fcad22 Device Boot Start End Sectors Size Id Type /dev/sdb1 * 64 5898239 5898176 2.8G 17 Hidden HPFS/NTFS /dev/sdb2 5898240 5899647 1408 704K 1 FAT12 Disk /dev/loop0: 2.6 Gi B, 2779897856 bytes, 5429488 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes @Arcaici Instead of writing (hd0,gpt6) there, write the actual name of your partition. I have a problem I got stuck in umount /mnt/sys It says umount : /mnt/sys: target is busy So, i started to skip umount /mnt/sys But when in the last command umount /mnt it says target is busy too In step mkdir /mnt/boot/efi says Cannot create directory *** file exists, when i started reboot, still no grub kali show, directly to the windows @stellarix I've again run those commands and the entry of grub has been successfully added in my boot menu options.

I found Rosa Image Writer, and I was able to install Kali without any issues. I have a laptop were i installed windows 10(it came with windows 8), and I am trying to install Kali 2017.2. Create a bootable (Kali 2017.2) USB using u Netbootin, this worked and I get the live, live persist etc. Partition my harddrive in Windows so that I have 100 GB unallocated space. Run ls to list the name of all partitions and show the output here. Yeah, the entry was removed when i did a firmware update so i again added it.

Leave a Reply